55%
Force reduction
← Timber Sports Flooring
ATHREN COURT · ATHREN T-D2
Double-Keel / Double-Batten Area-Elastic Timber System
Fixed area-elastic timber sports-floor pathway using upper and lower timber support layers separated by resilient cushioning, with a lower levelling / shock-support layer.
158approx. mm nominal build height · adjustable
Documented build-up
Layer by layer.
- Layer 01
- A-class birch playing-surface pathway · current installation source shows approx. 20/22 mm × 60–80 mm × 1800 mm
- Layer 02
- 0.5 mm EPE moisture-control membrane
- Layer 03
- 19 mm solid-pine subfloor in current installation source
- Layer 04
- 45 × 45 mm upper solid-pine battens
- Layer 05
- 8 mm intermediate resilient rubber pads at upper/lower batten intersections
- Layer 06
- 45 × 45 mm lower solid-pine battens
- Layer 07
- 19 mm lower resilient rubber levelling / shock-support layer
- Overall height
- Approx. 158 mm · adjustable
- Installation type
- Suspended timber sports-floor pathway
2020 laboratory reference
Measured performance for the corresponding submitted sample.
Laboratory report performance reference only. The tested sample records an 18 mm subfloor. The report is not a Certificate of Approval and does not establish current production equivalence.
1.6 mm
Vertical deformation
93%
Ball rebound
84
Slip resistance
68 mg
Resistance-to-wear mass loss
0.44 mm
Rolling-load indentation
Two manufacturer timber-floor samples were tested under the FIBA Equipment & Venue Centre Approval Programme in 2020 and recorded as PASS against the submitted Level 2 wooden-floor requirements. The reports are laboratory test reports, not Certificates of Approval.
ATHREN · technical diagrams
Two sprung timber systems, drawn as complete floor build-ups.
These original diagrams translate the current installation documents into a clean ATHREN planning language. They show documented layer order and nominal build heights, while disputed spacing and model-specific performance remain deliberately unlabelled.
T-01
SINGLE-BATTEN SYSTEM
Approx. 105 mm suspended build-up.
Birch playing surface over moisture control, solid-pine subfloor, timber battens and resilient rubber support.
T-02
DOUBLE-BATTEN SYSTEM
Approx. 158 mm suspended build-up.
Two timber batten layers separated by intermediate resilient pads, over a lower resilient levelling layer.
T-03
BASE + EXPANSION COORDINATION
Slab flatness, expansion and ventilation belong in the same floor brief.
Current instructions document a ≤5 mm / 2 m base check, perimeter expansion, intermediate movement provisions and finished-floor ventilation.
Project-specific selection
Check the hall before freezing the floor.
Confirm slab flatness, moisture, finished floor level, underfloor services, equipment sockets, line marking, event use and local installation responsibilities.
Direct project answers
What project teams need to know about this ATHREN timber-flooring pathway.
What is ATHREN T-D2 Double-Keel Timber System?
Approx. 158 mm adjustable double-keel / double-batten timber sports-floor pathway with upper/lower 45 × 45 mm supports and 8 mm intermediate resilient…
What projects are suitable for athren t-d2 double-keel timber system?
Typical project pathways include residential projects, commercial projects, hospitality projects, and international projects. Final suitability depends on the exact configuration, site conditions, operating requirements and destination.
What information is needed to specify athren t-d2 double-keel timber system?
Before specification or quotation, the project review should confirm: Verified product specifications or documented product facts; Clear applications, limitations and configuration boundaries; Project inputs required for manual quotation or technical review; Apollo supply-only scope and purchaser/local-project responsibilities. Claims are kept tied to the exact proposed system rather than transferred from a related product or reference configuration.
Can Apollo NZ Global supply athren t-d2 double-keel timber system internationally?
Apollo can supply suitable projects internationally where the product and destination pathway are current. Send the project location, intended use, dimensions or quantities, timing, relevant drawings or photographs, and any known performance, compliance or environmental requirements for review.